Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across San Fernando
Gate parts and welding in San Fernando usually means one of two things: a hinge post has finally rusted through, or a gate that worked fine for thirty years now drags, binds, or won’t stay shut. We fix both, right in your driveway, with welding done on site. Hal Gatewood has been at this since 2001, and his crew knows the difference between a San Fernando permit and an LA City one. If your gate is sagging, jumping its track, or the operator is straining itself to death, call (818) 514-7606. We’ll answer in person, not with a recording.
Why Gatewood Fence & Gate Is San Fernando’s Preferred Gate Parts & Welding Company
We’re not a franchise with a rotating cast. The same crew that shows up in Sylmar shows up on Brand Boulevard and Maclay Avenue. The name is on the shop, and the shop is down the road, which is the oldest accountability there is. Every job we do in San Fernando, from a new hinge on a Calvert Street pedestrian gate to a full post replacement off Foothill Boulevard, carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround, no re-diagnosis fee, no “that’s a different department.”
San Fernando homeowners have a specific problem: most of these gates went in during the 1980s and 1990s, and the original hardware is done. Hinges are egged out, latch plates don’t line up, roller bearings are flat-spotted. We see it daily. That’s why we keep parts on the truck for the common failures: DoorKing hinge bushings, Mighty Mule roller brackets, Elite latch hardware. We don’t tell you to wait a week for a part that should have been in the van. Pricing is upfront, agreed before we touch anything, and we’ll give you a free second opinion on any written estimate, even if it means telling you the other guy’s number was fair.
Our Gate Parts & Welding Services in San Fernando
Hinge Replacement
A gate sags in the hinge post, not in the middle. That’s where we start. Most 1980s-era San Fernando gates used barrel hinges welded directly to the post. Thirty-plus years of 105°F summers and Santa Ana winds have wallowed out the pin holes and cracked the weld at the barrel. We cut the old hinge off, face the post clean, and weld a new hinge set rated for the gate’s actual weight, not the lightest one on the shelf. On a gate that gets opened six times a day, a proper hinge replacement in San Fernando typically runs $220 to $430 per hinge set, depending on gate weight and post condition.
Post Replacement
The alkaline soil in this part of the Valley eats steel. Original hinge posts set in the 1980s rust through below grade where you can’t see it, then the whole gate leans and the slide track binds. We dig out the old post, set a new schedule 40 steel post in concrete, and weld the gate back in true. If the gate is drive-on slide style, we re-check the rack and pinion alignment after. Post replacement in San Fernando runs $480 to $850 for a standard pedestrian or single swing gate post. Wide driveway posts run higher because of the concrete pour and lag time for cure before hanging the gate.
Rail Repair
Slide gate rails take the most abuse in San Fernando. A bent lower rail from a tire clip, a rusted splice from thirty years of irrigation overspray, or a worn rack gear missing teeth. We don’t replace the whole gate when the rail is the only failing part. We cut out the bad section, weld in fresh steel, and re-align the rollers. Most rail repairs here come in at $260 to $500, including the on-site weld and a roller check. If the gate came off its track, the repair includes resetting it and testing the opener’s limit travel.
Custom Welding
Sometimes the fix is stronger than the original. We weld cracked gate frames, build new picket sections to match existing ornamental work, reinforce hinge plates, and add receiver hitches or custom latch mounts. For San Fernando’s older bungalows and ranch homes with ornamental wrought iron, a custom weld that matches the original scrollwork saves you from replacing an entire matching gate because one scroll cracked. Match work runs $180 to $390 per section, while heavier structural welds are quoted on the spot. Same-day quotes written down, agreed before we light the torch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in San Fernando
We’re certified to service nine major gate brands, but around San Fernando the ones we see most are DoorKing, Elite, Mighty Mule, and LiftMaster. Parts for those sit on the truck. If your DoorKing operator is grinding, or your Elite board is throwing a code, or your Mighty Mule arm won’t travel, we diagnose it accurately the first time because we’ve worked on hundreds of them. Our Gate Parts & Welding team stocks the common consumable parts local to this market so we’re not quoting you a two-week lead time on a hinge bushing that should have been in the van. That matters when your gate is the only thing keeping the driveway closed.
Common Gate Parts & Welding Problems We See in San Fernando Homes
- Rusted hinge posts from 1980s installs. The original steel was set directly in concrete with no post cap. Alkaline soil wicks moisture up, the base rusts through, and the gate leans until the slide track operator grinds its own gears to death. We replace the post and re-set the gate, not just the visible bracket.
- Summer heat expansion misaligning strikes and latches. At 105°F+ in the Valley, a metal gate frame grows enough that a keypad entry strike plate that worked in January won’t line up in August. The operator pushes harder, the limit switches overheat, and eventually the board fails. We re-set the strike with a summer gap allowance and check surface temps on the operator.
- Santa Ana winds bending pedestrian gates off their stops. Fall winds funnel through the San Fernando Valley with serious force. A lighter pedestrian gate with no wind stay can bow or jump its guide stop entirely. We straighten the frame, add a positive stop, and test the safety photocell so the operator doesn’t reverse erratically when a wind gust trips the beam.
- Rack and pinion wear on 1990s slide gates. Slide gates installed on homes facing Maclay, San Fernando Road, or Truman Street have opened thousands of times. Rack teeth wear unevenly, the pinion slips, and the gate jerks or stalls. We replace the rack section or the pinion gear, not the whole operator.
Pricing for Gate Parts & Welding in San Fernando, CA
Here’s what you can expect to pay in San Fernando, with everything quoted and agreed before work starts. Hinge replacement typically runs $220 to $430 per hinge set. Post replacement runs $480 to $850 for standard posts, higher for wide driveway gates. Rail repair runs $260 to $500. Custom welding varies by the linear foot, but most repairs land between $180 and $390 per section. Full gate panel rebuilds on ornamental wrought iron usually run $900 to $1,600. Why do prices cluster where they do? Gate weight, post depth, and whether the operator needs re-alignment after. We quote the job, you approve it, and that number does not change when we show up. The only time a number changes is if we open something up and find hidden damage, and we stop and call you first. No pick-a-number games. Call (818) 514-7606 for a written quote. It’s free.
One Thing Most San Fernando Homeowners Don’t Know About Permits
The City of San Fernando is its own jurisdiction, completely encircled by the City of Los Angeles. That means a gate repair involving structural welding or motorized operator work pulls a City of San Fernando Building & Safety permit, not an LA City permit. Valley contractors who run LA City permits by habit get this wrong, and the homeowner is left holding unpermitted work with no final inspection record. If a contractor tells you no permit is needed for a new welded post, check with Building & Safety yourself. We know the San Fernando process because we’ve pulled these permits before. Same inspectors, same counter. The paperwork doesn’t scare us.
Key Takeaways
- Gate parts and welding repairs in San Fernando run $180 to $1,600 depending on the job, quoted and agreed before work starts.
- Structural welding or motorized gate work inside the City of San Fernando requires a City of San Fernando permit, not an LA City one.
- We weld on site, keep your gate in your driveway, and stock parts for DoorKing, Elite, Mighty Mule, and LiftMaster.
- Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, Hal returns. One call.
- Calls are answered by a live person 24/7. That’s not a marketing line. Try it at (818) 514-7606.
We Also Serve Cities Near San Fernando
We work throughout the northeast Valley and into the foothills. If you’re in Sylmar, Granada Hills, Northridge, or Van Nuys, you can read more about Gate Parts & Welding in San Fernando or call us for your own street. The truck that shows up is the same one that works San Fernando daily, and the person on the phone knows the area without looking at a map.
Serving San Fernando, CA - Our Local Coverage Area
We’re based in the San Fernando area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in San Fernando
Yes, if the hinge post is structural to the gate and you’re cutting out and re-setting it with new concrete and a welded attachment, the City of San Fernando Building & Safety department treats that as structural work. A simple hinge replacement on an existing post usually does not require a permit, but a full post pull and set does. We handle the permit for you and schedule the inspection. Call (818) 514-7606 and we’ll tell you which path your gate falls into before you commit to anything.
Yes. We add solar panels and battery packages to FAAC operators regularly for gates off Foothill Boulevard and other long-driveway properties where running AC power to the entry would cost more than the gate itself. A solar conversion with panel, charge controller, and battery typically runs $650 to $1,100 in San Fernando, plus any operator board changes. We’ll check your FAAC model’s amp draw and sunlight exposure before quoting. Free estimate, agreed before install.
Fall Santa Ana winds push the gate sideways, and if the guide rollers or lower rail are worn, the gate climbs the roller flange and jumps. Combine that with a 30-year-old rail with flat spots, and it happens every wind event. We replace the worn rail section or rollers, re-set the guide clearance, and add a wind stop so the gate stays seated. Most San Fernando slide gate re-alignments run $300 to $550.
Often the latch itself is fine and the post has moved, or the gate frame has sagged at the hinge welds. We re-align the gate first, then address the latch. If the latch plate has worn through, we weld in a fresh plate and re-set the catch. On older bungalow gates with the original 1940s-1950s ornamental work, a careful weld is always safer than replacing the latch assembly with something that doesn’t match. Latch repairs in San Fernando typically run $120 to $260.
Yes. Any motorized gate must meet current entrapment protection standards, and a safety photocell and reverse mechanism are part of that. A 1990s gate that never had a photocell installed is a serious safety issue, especially with children or delivery drivers in the path. We install and test photocells on older operators regularly, and it runs $180 to $350 per cell in San Fernando, including the wiring run. We’ll also test the operator’s reverse force while we’re there.
Call Gatewood Fence & Gate for Gate Parts & Welding in San Fernando
If your gate is sagging, grinding, jumping, or just not latching, call (818) 514-7606. We answer live. We’ll give you an honest read on what’s failing, whether it’s a weld, a roller, a post, or an operator, and a written price before we touch anything. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every job. Hal Gatewood’s name is on the invoice. That matters more than any warranty language.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving San Fernando since 2001.