Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Reseda
Gate parts and welding in Reseda usually means one of three things: a hinge post that’s shifted out of plumb, a slide gate rack that’s binding, or an operator that won’t hold a signal. We see all three every week, and most jobs are done the same day we show up. Gatewood Fence & Gate has been fixing gates in the San Fernando Valley since 2001, and we weld on site in your driveway so the gate never leaves your property. Call (818) 514-7606 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Reseda’s Preferred Gate Parts & Welding Company
Reseda is dense. Sherman Way, Reseda Boulevard, Saticoy Street. Shared driveways, apartment parking lots, block-wall perimeters with slide gates retrofitted where a swing gate never fit. That’s the work we do most, and we’ve done it long enough to know that a gate in Reseda doesn’t fail the way a gate in Tarzana or Encino fails. The heat out here on the Valley floor sits 15 to 20 degrees above the coastal side all summer, and it cooks aluminum frames, motor windings, and rubber seals faster than any manufacturer’s lifespan chart accounts for.
Hal Gatewood’s name is on the shop. The address is published, the license number is published. You can call and get him on the phone, or you can drive in and talk to him face to face. That’s the kind of accountability a homeowner who’s been burned by a phone quote before actually wants. Every job carries the 90-Day Done Right Promise in writing, not buried in fine print. If it’s not done right, we come back and make it right. One call does it.
We answer the phone with a live person 24 hours a day. Not a voicemail, not a call center three states away. When a gate jams shut on a shared driveway at 7 a.m. and six tenants can’t get to work, you talk to a person who knows Reseda, not a script.
Our Gate Parts & Welding Services in Reseda
Hinge Replacement
A gate sags in the hinge post, not in the middle. Pull a sagging gate back with a turnbuckle or shim the hinge and you’ve bought a few months, not a fix. In Reseda, where the expansive clay soil heaves post footings every late winter, hinge replacement usually means the post is out of plumb too. We cut out the old hinge, weld in a new one rated for the weight of the gate, and set the post correctly before re-hanging. On narrow shared driveways along Reseda Boulevard, we work in the footprint of the gate itself so tenant vehicles keep moving.
Most hinge replacements in Reseda run $180-$320 per hinge, post work included if it’s just an adjustment. If the post has cracked at the weld plate or the footing has heaved, you’re looking at post replacement on top of that.
Post Replacement
Reseda’s soil is clay and it moves. Every late winter, when the rain soaks in and the ground swells, we see hinge posts that have been pushed half an inch to an inch out of plumb. A gate hung on that post binds, drags, and eventually destroys the rollers. We dig out the old footing, pour a new one deeper than the original, and weld a new post in true before re-hanging the gate the same day. Concrete cures while the gate is already working again.
Post replacement in Reseda typically runs $350-$600 per post depending on depth and whether we’re doing full demolition of the old footing or just a reset.
Rail Repair
Slide gates live and die by the rail and rack. When the rack weld breaks or the rail sags from years of Valley heat taking the temper out of the steel, the operator strains against it and burns out motors. We see this exact failure on 1980s apartment complexes off Sherman Way all the time. We cut out the damaged section, weld in new rack stock, and realign the pinion so the motor isn’t fighting the gate. If the rail itself has sagged, we weld gussets or replace the section rather than just tightening bolts.
Rail and rack repair in Reseda runs $250-$450 for a typical section repair. Full rail replacement on a long driveway gate runs higher, and we give you a written price before we start.
Custom Welding
Not every gate failure matches a parts catalog. Tenants back into them. The earthquake brace gets bent. A previous contractor welds a patch that makes the whole frame twist. We weld on site, in the driveway, so you watch the work happen. Custom welding covers cracked frames, broken hinge brackets, bent stiles, and the oddball retrofits that Reseda’s older tract homes accumulate over 50 or 60 years. If we can weld it true, we fix it. We don’t sell you a new gate because welding takes an hour longer.
Custom welding in Reseda runs $150-$400 per job for straightforward frame and bracket repairs. If the damage is extensive, we quote it before firing the torch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Reseda
We carry parts for DoorKing, Elite, Mighty Mule, and LiftMaster on the truck, which means most Reseda gate repairs don’t wait on a parts order. That matters in a city where a downed gate on a shared driveway is a tenant complaint waiting to happen. We’re certified to service nine major gate brands total, but the four above are what Reseda’s housing stock actually uses, and we keep the common rail stock, rollers, hinges, and receiver boards in stock locally. If a part has to be ordered, you’ll know before we leave the driveway, not after.
Common Gate Parts & Welding Problems We See in Reseda Homes
- Corroded aluminum low-voltage wiring on 1990s Apollo and Linear operators. Junction boxes on Reseda apartment complexes have been baking in Valley heat for 30 years, and the connections corrode. The operator throws a fault code, and a new motor doesn’t fix it because the wire is the problem. We rework the runs, not just the motor.
- Heaved hinge posts from expansive clay soil. Every late winter, Reseda’s clay soil swells and pushes concrete post footings out of plumb. The gate starts dragging, the rollers bind, and the operator strains until something burns out. We set posts deeper and check plumb before re-hanging.
- Warped aluminum frames from extreme summer heat. Reseda’s interior heat regularly crosses 105°F in the summer, and aluminum frames expand and warp. Seals degrade, stiles twist, and the gate binds at the latch. We weld reinforcing gussets where the frame has twisted, instead of telling you to replace the whole thing.
- Failed slide gate rollers on narrow shared driveways. On Reseda’s post-WWII lots with tight right-of-way space, slide gates run constantly and the rollers wear flat or seize. Tenants can’t get out. We replace rollers and realign the rack so the gate doesn’t eat itself in another season.
Pricing for Gate Parts & Welding in Reseda, CA
Here’s what you can expect to pay for gate parts and welding in Reseda, based on what we actually charge on the street:
- Hinge replacement: $180-$320 per hinge
- Post replacement: $350-$600 per post
- Rail and rack repair: $250-$450 per section
- Custom welding: $150-$400 per job
- Gate rollers: $120-$250 per set, including realignment
- Latch and lock replacement: $95-$220 per assembly
The price you’re quoted is the price you pay, and it’s agreed before we start. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. When heat and clay soil have done a number on your gate, you want a written number before the torch fires. Call (818) 514-7606 and we’ll give you one.
We Also Serve Cities Near Reseda
We work throughout the Valley, and if you live in Tarzana, Northridge, Encino, or Canoga Park, you’re a short drive from our trucks. When Reseda customers need gate work, they call us because we’re local and we weld on site. For the full scope of what we do, see our Gate Parts & Welding service page or the Gate Parts & Welding in Reseda page for the neighborhood-level detail.
Serving Reseda, CA - Our Local Coverage Area
We’re based in the Reseda area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Reseda
Reseda’s 1980s apartment complexes along Sherman Way and Reseda Boulevard installed slide gates during a late-1980s security upgrade wave, and those operators are now 30 to 35 years old. The Valley heat bakes motor windings and degrades low-voltage wiring, and the clay soil heaves post footings so the rack and pinion bind. Add constant tenant cycling and the gate fails from accumulated damage, not one single breakdown. We fix it in place so the driveway stays open for tenants while we work. Call (818) 514-7606 for a quote on your complex’s gate.
Yes, in most cases. A sagging gate usually means the hinge post has moved out of plumb or the hinges have worn at the weld. We re-set and weld the post, replace the hinges, and the gate hangs true again. The frame itself is rarely the problem, and we don’t sell new gates to fix a hinge post. On Reseda’s narrow lot lines, we do all of it in place, so your tenants keep coming and going.
The fault codes are usually from corroded aluminum low-voltage wiring at the junction boxes, not the motor itself. We see this constantly on 1990s-era Apollo and Linear operators across Reseda. If we only replace the motor and leave the corroded runs, the fault codes come back within a season. We inspect and rework the low-voltage wiring at the same time as the operator replacement, so the fix lasts. If you’re seeing fault codes, call (818) 514-7606 and we’ll trace the circuit.
Yes. We work in the footprint of the gate itself and keep the driveway operational while we weld and replace hinges. On shared driveways in Reseda where tenants can’t park on the street all day, we plan the work so the gate swings or slides again within a few hours, not at the end of the day. The post sets while the gate is already functioning, and we clean up before we leave.
The permanent fix is replacing the rollers and realigning the rack and pinion so the gate isn’t fighting itself. Reseda’s summer heat degrades roller bearings and the clay soil shifts the track, so just greasing them buys you a few weeks. We replace the roller sets, set the track true, and realign the rack so the operator doesn’t strain. Call (818) 514-7606 and we’ll give you a written price for the roller replacement and alignment. Estimates are free.
Call Gatewood Fence & Gate for Gate Parts & Welding in Reseda
When your gate is down on a shared driveway off Sherman Way, or the hinge post has heaved out of plumb on a 1950s tract home, you need a welder who knows Reseda’s soil, heat, and housing stock. You need someone who answers the phone. Call (818) 514-7606 and talk to Hal Gatewood or his crew. We weld on site, we quote before we start, and every job carries the 90-Day Done Right Promise in writing. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Reseda since 2001.