Ghost Controls Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Parts & Welding in Tarzana: What to Know First

We repair Ghost Controls gate openers and weld the steel that holds them, right here in Tarzana. Most Ghost Controls parts and welding jobs run $190-$680 depending on what actually failed, and we give you the real number before any work starts, with a free estimate. If you’ve got a Ghost Controls gate that won’t close, sags, or grinds against the post, call (818) 514-7606 and a live person answers.

Call (818) 514-7606

This page is for Ghost Controls owners in Tarzana who need hinges, posts, rail sections, rollers, latches, or custom welding done without hauling the gate off. We’re an independent Ghost Controls service provider, not a factory authorized shop, which means we fix what’s broken instead of selling you a new operator because that’s what the book says.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls makes a solid residential operator, but the operator is only half the story. The gate itself takes the beating, and after years in Tarzana sun and the occasional Santa Ana wind, the steel and hardware give out first. Here are the failures we see most on Ghost Controls gates around here:

• Hinge weld fatigue on the Ghost Controls single-arm line. The AXS and TSS1 single-swing setups put every pound of gate weight on two hinge welds. When those welds crack, the gate drops a quarter inch and the operator’s arm starts fighting a gate that isn’t hanging square. We grind out the old weld, true the gate, and weld it back in place. Replace the hinges and you’ll be back in the same spot in a year. Weld them right and they’ll outlast the motor.
• Post lean from soft Tarzana soil. Tarzana sits on a lot of decomposed granite and clay that shifts with rain and drought. A Ghost Controls swing gate mounted to a post that’s drifted three degrees off plumb will throw the opener’s limit settings and stall mid-cycle. The operator didn’t fail. The post did. We dig, reset, and weld a fresh bracket plate to the post so the arm engages clean.
• Rail separation on Ghost Controls slide gates. The GTS slide line uses a chain and sprocket, but the rail sections underneath take rocks, mud, and a decade of weather. When a rail section separates at the splice, the gate jerks, binds, and the motor overloads. We weld the splice or drop in a new section, then align the wheels so the load spreads evenly. A new motor won’t fix a broken rail, and we won’t sell you one to find out.
• Latch and lock misalignment after years of use. The Ghost Controls swing line relies on a mechanical latch that has to meet the post dead on. When hinges sag even half an inch, the latch misses the striker and the operator fights to hold the gate shut. Rather than force it with the motor’s pressure settings, we re-weld the striker plate in the right position. The gate closes, the latch catches, and the motor stops working double duty.
• Worn gate rollers on heavier Ghost Controls gates. Big custom gates on Tarzana properties sometimes run larger Ghost Controls operators with the gate rolling on steel V-rollers. When those rollers flatten, the gate drags and the operator’s current draw spikes. We replace the rollers and weld new roller plates if the old ones are chewed up. Cheap aftermarket rollers last about one rainy season. We use ones that hold up.

Our Ghost Controls Gate Parts & Welding Process

Every Ghost Controls job we do in Tarzana follows the same order, because skipping a step is how gates end up back in the same condition six months later.

1. 1
   You call (818) 514-7606. A live person picks up, asks what the gate is doing, and schedules a time that works. No call tree, no chat widget.
2. 2
   We show up and look at the whole gate. The operator, the arm, the hinges, the welds, the post, the rail, the latch. A Ghost Controls operator rarely fails without a reason, so we find the reason before we quote a fix.
3. 3
   We give you the number before any work starts. The price is quoted and agreed before anything gets welded or unbolted. You won’t get a call saying the scope changed and the price doubled.
4. 4
   We decide on OEM or quality aftermarket parts together. Ghost Controls OEM parts keep you squarely in warranty territory. Some aftermarket parts like hinges, rollers, and bracket plates are genuinely better than factory, and we’ll tell you which is which. We never push a part that doesn’t need replacing.
5. 5
   We weld on site, in your driveway. Your gate stays on your property. The weld is done with the gate in its actual position, so the alignment is real, not a jig in a shop.
6. 6
   We test the full cycle and hand you the 90-Day Done Right Promise in writing. Open, close, latch, limit check, motor draw check. If it isn’t right, one call brings us back.

What Ghost Controls Gate Parts & Welding Costs in Tarzana

Here are the numbers we actually give Ghost Controls owners in Tarzana. These are honest ranges, not a phone-call hook:

• Hinge replacement (welded, not bolted): $220-$390 per hinge, including the bracket and weld. A sagging gate usually needs both hinges done.
• Post replacement with bracket welding: $480-$950 depending on post depth, concrete, and whether it’s a swing or slide post.
• Rail section repair or splice weld: $190-$410 depending on section length and whether we’re splicing or replacing.
• Custom welding (reinforcement, crack repair, safety-edge mounts): $150-$550 depending on what we’re cutting and re-joining.
• Gate roller replacement with plate welding: $180-$360 per roller set.
• Latch and lock retention (weld striker plate, realign): $140-$280.

What moves the price is steel thickness, whether we’re fighting old rust or previous bad welds, and how deep the post is set. You’ll know the cost before we light the torch. Call (818) 514-7606 and we’ll come out free of charge and quote it straight.

Why Tarzana Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

Hal Gatewood has been fixing gates in Tarzana since 2001, and most of his customers live within a few miles of Ventura Boulevard. Some have been calling him back for going on two decades. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.

We also work on the other brands sitting on Tarzana properties: LiftMaster, Mighty Mule, DoorKing, and the rest. That matters when you’ve got a Ghost Controls operator on one gate and something else on the side entrance. One crew, one guarantee, no passing the blame.

Every job carries the 90-Day Done Right Promise in writing. Hand me your number and I’ll call you when I’m on my way - none of that four-hour window stuff. We’re licensed, insured, and a live person answers 24/7. Seniors and veterans get 10% off, and we knock $40 off any repair over $200.

FAQs