DoorKing Gate Repair Nationwide | Gatewood Fence & Gate

DoorKing Gate Repair in Tarzana: What to Know First

DoorKing gate repair in Tarzana is work we handle regularly, and most jobs are done in one visit: diagnose the problem, replace the worn part with OEM or a quality equivalent, and get the gate moving right again. You’ll pay $85 to $145 for the service call and diagnosis, and most repairs land between $240 and $680 depending on what actually failed. Nobody at our shop quotes a price over the phone and then adds to it at your driveway. If you own a DoorKing operator and the gate is grinding, stalling, or refusing to close, call (818) 514-7606 and a live person answers.

Call (818) 514-7606

Hal Gatewood has been fixing gates in Tarzana since 2001, and DoorKing operators account for a good share of the calls we take from homeowners along Ventura Boulevard and the streets that branch off it. This page is for you if you’ve got a DoorKing 9150, 6500, 6002, or any of the gate operators that DoorKing has sold for the past couple of decades and something has stopped working the way it should.

How DoorKing Products Fail in Tarzana, and How We Fix Them

• DoorKing 9150 slide gate operators burning through limit switches. The 9150 is a workhorse, but in Tarzana we regularly see the limit switch contacts arc and pit from the heat and dust. The gate will sail past its stop point or slam into the end bracket. We replace the limit switch assembly with the OEM DoorKing part, realign the stops, and test the gate through fifty cycles before we call it done.
• DoorKing 6500 swing gate motor capacitors dying in the San Fernando Valley heat. A capacitor that gives out leaves the motor humming but not turning. Homeowners tell us the arm moves an inch and quits. We keep DoorKing-rated capacitors on the truck for the 6500 and 6002 series, and we’ll check the capacitor first before we sell you a whole new operator, which is something our competition out here does not always do.
• DoorKing keypads and telephone entry systems losing relay function. The keypad lights up, the code beeps, and the gate does not move. Nine times out of ten it is a failed relay or a corroded connection at the control board, not the keypad itself. We bench-test the board, replace the relay if that is what died, and you keep your existing keypad instead of buying a new one.
• Hinge and post wear on DoorKing swing gates. The operator gets blamed when the gate grinds, but a sagging hinge post will make any operator work twice as hard until it burns out. We fix the post and the hinge in your driveway, with on-site welding, because a gate sags in the hinge post, not in the middle, and that is where we start.
• Older DoorKing 6002 operators with stripped plastic drive gears. The 6002 has a plastic gear in the drive train that strips after years of hard use. DoorKing sells the gear, and it is worth replacing rather than scrapping a perfectly good motor. We carry the gear and we’ll swap it for less than a new operator costs by a long shot.

Our DoorKing Gate Repair Process

1. 1
   You call. A live person answers, day or night. We ask what the gate is doing and what model DoorKing you have, if you know it. Then we give you a straight answer about whether it sounds like a same-day job or something we’ll schedule.
2. 2
   We show up and diagnose. Hal or one of his crew checks the operator, the board, the limits, the hinges, and the power supply. We do not guess and we do not charge by the hour to stand around looking puzzled.
3. 3
   We write the price before we touch a tool. You get a firm number for parts and labor. That price does not change unless you ask us to do something extra, and even then we’ll tell you the new number first.
4. 4
   We repair it on site. DoorKing parts go in where OEM matters, and we’ll tell you honestly when a quality aftermarket part does the same job for less. We weld what needs welding right there in your driveway.
5. 5
   We test the gate hard. We run open and close cycles, check the safety edges and photo eyes, and listen to the motor. If the gate is supposed to reverse when it hits something, we make sure it reverses.
6. 6
   You get the 90-Day Done Right Promise in writing. If it is not done right, we make it right. One call brings us back, no runaround.

What DoorKing Gate Repair Costs in Tarzana

Here are honest numbers for the DoorKing jobs we do most in Tarzana:

• Service call and diagnosis: $85-$145
• Limit switch replacement on a 9150: $180-$310
• Capacitor replacement on a 6500 or 6002: $140-$240
• Keypad relay or control board repair: $190-$350
• Hinge and post weld repair: $260-$550
• Drive gear replacement on a 6002: $220-$390

What moves the price is parts cost, whether we need to weld, and how deep the trouble goes once we open things up. Every number above is quoted and agreed before any work starts. And we have standing offers that make the math easier: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (818) 514-7606 and we’ll give you a real number, not a range with a shrug.

Why Tarzana Homeowners Call Gatewood Fence & Gate for DoorKing Work

We have been at this since 2001, and Hal Gatewood’s name is on the shop and on every invoice. We are not a franchise and we are not three states away. When your DoorKing gate goes down, the person who shows up lives and works in the same part of the Valley you do, and he will hand you his number and say, “Hand me your number and I’ll call you when I’m on my way - none of that four-hour window stuff.” We also service LiftMaster, Mighty Mule, and Ghost Controls, so if you’ve got more than one gate or a neighbor with a different brand, we’re already the people to call. Every job carries our 90-Day Done Right Promise. It is not a slogan. It is written on the paperwork you keep.

FAQs