Linear Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Linear Gate Parts & Welding in Tarzana: What to Know First

We provide independent Linear gate parts and welding in Tarzana, and most hinge replacements or track repairs get done same-day because we weld on site in your driveway instead of hauling the gate to a shop. Typical Linear hinge or latch work runs between $180 and $400, and every price is quoted and agreed before we touch a torch. You own a Linear operator, but the steel under it is what usually fails first, and that’s where we start.

Call (818) 514-7606

If you live in Tarzana and your gate grinds, sags, or won’t stay latched, call Hal Gatewood at (818) 514-7606. We’ve been fixing Linear-equipped gates in this neighborhood since 2001.

How Linear Products Fail - and How We Fix Them

Linear builds a decent operator. The steel it sits on is another story, and in Tarzana the summer heat plus the fine dust off the 101 chew through cheap hardware faster than most people expect. Here’s what we see on Linear jobs week after week:

• Hinge post lean on Linear slide gates. Linear slide gate operators (the SL series and the older LS models) push a lot of weight against the rear post. In Tarzana, where half the driveways are on a slight grade and the soil is heavy clay that expands and contracts all year, those posts migrate. The gate starts to drag, the operator pulls extra amps, and the circuit board eventually burns out. We dig out the post, set a new one in concrete, and weld the hinge brackets back square. Fix the panel without the post and you’ll fix it twice.
• Welded hinge barrels that seize up. Tarzana’s dry season dust gets into the hinge barrels on swing gates and turns the grease into grinding paste. Linear swing operators (the M and HS series) don’t have the torque to muscle through a seized hinge, so the motor stalls and the homeowner thinks the operator died. Most of the time the operator’s fine. We cut off the old hinges, weld on greasable barrels, and reset the leaf so it swings with two fingers.
• Broken welds on Linear cantilever gate frames. Cantilever gates ride on rollers and carry their own weight from the top rail. When the factory welds on the diagonal bracing start to crack, the gate sags, the rollers wear oval, and every cycle scrapes metal off the track. This is one of the most common Linear repairs we do in Tarzana. We weld the cracked joints, add a gusset where the stress concentrates, and replace the rollers before they trash the track.
• Latch and receiver misalignment after earthquakes. Tarzana sits near enough to the Northridge fault that even small shakers shift gate posts. A Linear LSO or LSO50 operator will throw a fault or refuse to close when the latch doesn’t line up with the receiver. We cut and re-weld the receiver plate or shim the post, then re-teach the operator’s limits. Most of these are a one-hour fix if caught before the operator burns itself out trying to force the issue.
• Linear OEM magnetic locks with failing brackets. The maglock itself is usually fine. The bracket it’s bolted to is a different story - we regularly find them installed with undersized fasteners or welded so thin that vibration cracks the bead. We replace the bracket, weld it properly to the post, and realign the armature plate so the lock holds on the first try.

Our Linear Gate Parts & Welding Process

Here’s what happens when you call us about a Linear gate that needs parts or welding in Tarzana:

1. 1
   You call and a live person answers. No voicemail, no phone tree. We ask what the gate is doing, what brand the operator is, and whether it’s swing or slide. Half the time we can tell you over the phone whether it’s a steel problem or an operator problem.
2. 2
   We show up and look at the whole gate, not just the complaint. A gate sags in the hinge post, not in the middle - and that is where we start. We check every weld, every roller, every bracket before we pick up a tool.
3. 3
   We give you a written price before any work starts. That price doesn’t change. If it needs a $2 part or $2,000 in steel work, you know before we strike an arc.
4. 4
   We weld on site. The gate stays in your driveway. We cut out the broken steel, prep the joint, weld it, and let it cool naturally. No hauling your gate across the valley to a shop.
5. 5
   We test it through a full cycle, twice. Manual cycle first, then under power with the Linear operator. If the operator has a force profile, we re-run the learn cycle so the motor isn’t fighting the repaired steel.
6. 6
   You get our 90-Day Done Right Promise in writing. If the weld cracks or the part fails inside 90 days, one call brings Hal back. No runaround.

What Linear Gate Parts & Welding Costs in Tarzana

Honest numbers, because you’ve earned the right to know before you decide to buy anything:

• Hinge replacement (single swing gate): $180-$350, depending on post condition and gate weight.
• Post replacement with re-welded hinges: $400-$800, including concrete and hardware.
• Weld repair on cracked frame or rail: $150-$450, depending on how much steel needs cutting and gusseting.
• Gate roller replacement (cantilever or slide): $120-$300 per pair, including track cleanup and alignment.
• Latch and receiver repair or re-weld: $140-$320, including adjusting the Linear operator’s limits afterward.

What moves the price most is whether the post under the problem is still good. A gate that’s been sagging for a year usually means the post gave up long before the hinge did. We’ll tell you which one it is and show you why. Estimates are free. Call (818) 514-7606 and we’ll give you a number you can hold us to.

Why Tarzana Homeowners Call Gatewood Fence & Gate for Linear Work

We’ve been fixing gates in Tarzana since 2001, and most of our customers live within a few miles of Ventura Boulevard. Some have been calling us back for going on two decades. That’s the kind of track record you build when your name is on the shop and your address is published for anybody to look up.

Every job carries our 90-Day Done Right Promise in writing. If it’s not done right, we make it right. Calls are answered by a live person 24/7, not a menu. And because we service nine major gate brands - Linear, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and four more - we don’t have to pretend a steel problem is an operator problem because we only know one brand. We’ll tell you what’s actually wrong, fix what needs fixing, and leave the rest alone.

FAQs